泄爆墻廠家與貴州省物資現代物流合作
泄爆墻操作工藝
1.工藝的流程
輕隔墻放線→安裝沿頂龍骨和沿地龍骨→豎向龍骨分檔→安裝豎向龍骨→安裝橫向龍骨卡檔→一側泄爆板→保溫材料填充→另一側泄爆板→施工縫隙做法→面層施工
2.放線:依據設計工程圖,在已做好的地面或地枕帶上,放出隔墻位置線.窗門洞口邊框線,并放好頂龍骨位置邊線
3.安裝門洞口框:放線后按設計,先將隔墻的門洞口框安裝完成.
4.安裝沿頂龍骨和沿地龍骨:按已放好的隔墻位置線,按線安裝頂龍骨和地龍骨,用膨脹螺栓固定于主體上,其螺栓間距為600mm.
5.豎龍骨分檔:依據隔墻放線門洞口位置,在安裝頂地龍骨后,按泄爆板的規格1220mm板寬,分檔規格尺寸為407mm或者610mm,不足模數的分檔應避開門洞框邊**塊罩面板位置,使破邊罩面板不在靠洞框處.
6.安裝龍骨:按分檔位置安裝豎龍骨,豎龍骨上下兩端插入沿頂龍骨及沿地龍骨,調節垂直及定位**后,用鏈接配件固定;靠墻.柱邊龍骨用膨脹螺栓與柱固定,釘距為1000mm
7.安裝橫向卡檔龍骨:依據設計要求,隔墻高度大于3m時應加橫向卡檔龍骨.
8.安裝罩面板
1)檢查龍骨安裝質量.門洞口框是不是相符設計及結構要求,龍骨距離是不是相符泄爆板寬度的模數
2)安裝一側的泄爆板,從屋門口處開始,無門洞口的墻體由墻的一端開始,泄爆板一般用M4自攻螺釘固定,板邊釘距為200mm,板中距離為300mm,螺釘距泄爆板邊緣的間距不得小于10mm,也不得大于16mm,自攻螺釘固定時,泄爆板必須與龍骨緊靠
3)安裝墻體內電管.電盒和電箱設備
4)安裝墻體內防火.隔音.防潮填充材料,與另一側泄爆板同時進行安裝填入
5)安裝墻體另一側泄爆板:安裝手段同**側泄爆板,其縫隙應與**側板面錯開
6)安裝泄爆板:第二層板的固定手段與**層共同,但第三層板的縫隙與**層錯開,不能與**層的縫隙落在同一龍骨上.
